LocoDialog Interface Tab.
Only set this to the IID you set in the rocrail.ini if your setup has more than one CS connected.
If this option is activated all Loco and Function commands will send to all connected Command stations.
The decoder address which range depends on the decoder type and underlying Command Station.
The optional secondary address can be used for WIO or T4T (TrainCoupling&CommunicationSystem).
Some Command Station, like the ESU Ecos, are using an Object ID instead of an address for referring to a specific loco.
This field can be left empty because the Ecos library can also look up locos by ID or address.
Some command stations do support multiple protocols; Check the user manual for details.
If the address is set to zero the protocol should be set to Analog for Track Driver support.
Note: Serverdefined, is the default mobile digital protocol used by the Command Station (CS). This setting is only of interest in case of multi protocol CS like Ecos/CSx(dcc/mfx). For a "DCC only" CS this option has no effect at all. Or for the Märklin 6051 its always Motorola.
If the Command Station cannot determine the decoder type itself you must specify the version as listed here ddx-en or found in the SRCP description. Most systems do not use this parameter because it is set directly in the CS or it does only support one version.
Number of speed steps the decoder is set up to. Rocrail needs the number of the decoder's speed steps e. g. to be able to calculate the wanted velocity in percent or KM/H.
The optional second speed steps can be used for T4T.
Number of extra functions supported by the decoder used. Default F0…F4.
The field on the right is the number of frames to skip. This will reduce CPU power and fluency of the video stream.
Note: Frames will also be skipped if the graphic processing is slow, even if this parameter is set to zero; The video stream cannot be paused.
The Roco video locomotive must be configured in "Client Mode".
This can be done with the Roco Videolok utility.
The port must be set to 5152.
Note: It can take up to 30 seconds before the first frames are coming in after starting the camera.
Note: If a train is assigned to the locomotive, and this train contains a car with a streaming camera, the camera of the car will be used instead.
Can be used:
A value of 5 is a good start to experiment with.
Some old Delta like decoders need some pause between a direction change and the last turnout command. With about 100ms this will do the trick when running DDX.
XpressNet does not propagate loco changes issued by throttles.
By activating this option, and if the loco is not in auto mode, every second a request is send to the Command Station to get the actual information needed to update the Rocrail clients.
Use with care. This option is not recommended and not supported in the Forum, and uses unnecessary CPU resources.
Inverts the hardware running direction.
This is an alternative to program the direction in the decoder by CV29.
A flag for correcting the BiDi, RailCom, direction in case the decoders is not correctly polarised.
See also: BiDi Direction
If WIO as Mobile decoder be used, this can simulate Vstart and Vhigh, CV2/CV5.
|3||PWM width factor||Example for 100 speed steps: 0=20kHz, 1000=10Hz|
The max. load for this locomotive in tons.
The CV3 range to use for loads between zero and max. load.
20130723.090557.995 r9999I cmdrD000 OLoc 2707 processing cmd="assigntrain" for [E03] 20130723.090557.995 r9999I cmdrD000 OLoc 2848 consist [train1] assigned to loco [E03] 20130723.090557.995 r9999I cmdrD000 OCar 0354 car [test] loaded weight  20130723.090557.995 r9999I cmdrD000 OLoc 2026 loco [E03] adjust acceleration: CV3=16 20130723.090557.995 r9999I cmdrD000 OVirtual 0437 program cmd=1 mode=0 20130723.090557.995 r9999I cmdrD000 OVirtual 0465 POM: set CV3 of loc 1003 to 16... 20130723.090557.995 r9999I cmdrD000 OLoc 2079 loco [E03] train length=56 weight=500