Hardware

Transportproblems like missing insurance options and the new VAT rules in EU (more administration) are changing GCA handling.
Due to changes of taxes administration in EU community, pricelist will only indicate prices without obligated VAT, TVA, MWSt, btw.,
Addional taxes (according the destination country) will be added on proforma invoice on ordering.
From this moment on, shipments will be done via Postnl, and ALL shipments with a value over € 80,00 will be insured.
Orders with a value below € 30,00 (excl. shipment, TVA, VAT, MwSt) will have extra charge of € 6,50 administration fee.
Orders can be made via email to peter@phgiling.net or via this order form
Paypal payment is possible, but ONLY when shipment is fully insured.

LocoNet® IO and LBuffer hardware by PhG.

• GCA50 LocoNet 16 ports unit based on PIC16F873A
• GCA50a LocoNet 16 ports unit based on Arduino Nano
• GCA500 LocoNet 16 ports unit with RJ12 connectors
• GCA51 LocoNet 2 x RFID + 8 Input Ports unit
• GCA85 LocoBuffer-RS232
• GCA91 LocoNet Patch Panel
• GCA101v2 LocoBuffer-Ethernet
• GCA123 16 button loconet switch board
• GCA124-8 LocoNet loc controller with 8 Function keys
• GCA141 Wheel counter
• GCA185 Arduino UNO LocoNet shield

CAN based hardware by RV & PHG.

• CAN-GCA Overview
• CAN-GC1 RS232/USB PC interface with 3 Amp power supply.
• CAN-GC1e V2 Ethernet PC interface.
• CAN-GCLN LocoNet Bridge.
• CAN-GC2 Universal 16 port I/O.
• CAN-GC2a Universal 14/16 port I/O with Arduino nano
• CAN-GC2G Multifunctional I/O.
• CAN-GC3 DCC Command Station with PT and ORD-3 connector.
  • ORD-3 3A Booster
• CAN-GC4 RFID Concentrator.
• CAN-GC5 Mobile keyboard and display. (CANCAB V2)
• CAN-GC6 4 Channel Servo Controller.
  • GCA137 Relay board
• CAN-GC7 Fast Clock.
• CAN-GC8 Display driver for dynamic text.
• CAN-GC12 16 key remote control for turnouts and signs
• PICAN_01 Combination of CAN and RocNet via Raspberry Pi
• CAN-ter Patchpanel for handheld CAN units

“Raspberry Pi" is a trademark of the Raspberry Pi Foundation.

• GCA-Pi01 Rasberry Pi HAT (Hardware Attached on Top
• GCA-Pi02 32 bits I/O board
• GCA-Pi03 16 channel PWM board (Servo's, LED-Signals, …)
• GCA-Pi04 RocMouse Discontinued
• GCA-Pi05 G-Scale Loc-decoder Discontinued
• GCA-Pi06 5V 3A Power Supply
• GCA-Pi07 Transformer current sensor Discontinued
• GCA-Pi08 16 x 40V / 100mA output module
• GCA41 Arduino Nano shield RFID RC522 interface
• PICAN_01 Combination of CAN and RocNet(GCA_PI01)**

• GCA41 Arduino Nano shield RFID RC522 interface
• GCA50a LocoNet 16 ports unit based on Arduino Nano
• GCA51 LocoNet® 2 x RFID + 8 Input Ports unit
• GCA185 Arduino UNO LocoIO shield
• G-ASH02 shield for 32 I/O with Arduino Mega (also in combination with DCC++ power driver shield)
• Multi colour led control with Arduino nano

SIOPico

• WIO_01(v2) : General I/O, Servo, LED, RFID, Display, Sensor, RailCom
• WIO_02(v2) : RCAN/MBUS/USB/WIFI General I/O, Servo, LED, RFID, Display, Sensor, RailCom
• WIO_03 : compact multi I/O unit
• WIO Rocrail system clock with 100mm display's also useable as standalone clock
• WIO_Control: WiFi Throttle
• WIO_CAN: MBUS/RCAN WiFi Interface
• WIO_Drive: compact DCC-CS and Mobile
• WIO_Boost: DCC CS
• WIO_Prog: DCC CS with extra H-Bridge for Programming Track. (Service Mode)
• WIO_Prog2 : DCC central station with programming track / CAN / RocNet . Output 2 x 3,5 Amp.
• WIO-VC-1: DCC CS high power up to 20A
• WIO_T1: Large scale turnout driver with 4 digital inputs.
• WIOPi_01 Wireless drive with Raspberry-Zero
• WIO_Pico_W_01 wireless multi I/O with Raspberry Pico W
• GCA214 RailCom reader
• RFID reader ID-12LA

• GCA174 DCC / Motorola Interface for GCA145
• GCA174mr Märklin/Fleischmann/Lenz TT simulator/interface for GCA145
• G-ASH03 DCC / Motorola servo/output decoder (= MARDEC)

• GCA_LM2 Serial Programmable Leds (SPL in Rocrail) Octal Led controller

Input- output extensions for GCA50(0), CAN-GC2, GCA_PI02 and WIO by GCA.

• Overview
• GCA_OK1 Isolated output level shifter for 3 to 5.5 V solutions
• GCA_OK2 Isolated input buffer for GCA145
• GCA01 Connector board for railplan modules
• GCA02 Relay board with 2 double pole, double task relays
• GCA08 Universal 1-3 Amp switching power supply
• GCA09 extra supply connection for LocoNet and CAN networks
• GCA21 Reverse loop-switch for heavy load.
• GCA41 Arduino Nano shield RFID RC522 interface
• GCA76 4 turnout extension driver for turnout coils > 0,5A
• GCA77 4 turnout extension driver for turnout coils < 0,5A
• GCA78 4 turnout extension driver for ac/dc turnout coils max 2 Amp
• GCA79 4 turnout extension driver for ac/dc turnout coils max 2 Amp
• GCA80 dcc function decoder to convert GCA79 into DCC turnout decoder
• GCA86 slow dimming LED signal extension
• GCA93 8 port current detector with signals
• GCA93_2_3_rail special unit for combined automatic traffic on Märklin K-Rail
• GCA94 8 port current detector with current transformers, for higher currents and lower powerloss..
• GCA98 EDits to DDX interface
• GCA100 polarity switch
• GCA102 Reverse loop switch with turnout control
• GCA107 Relay board extension
• GCA115 Stand alone servo driver
• GCA116 Bascule bridge lifter
• GCA120 Heavy load relay unit
• GCA122 Reversal switch
• GCA125 Extension for 8 motor- or single coil powered turnouts
• GCA126 Extension for Motor powered turnouts with feed-back
• GCA127 Extension for indication with 8 or 16 Leds
• GCA128L Switch / pushbutton test-unit for GCA50/CAN-GC2/GCA_PI02/GCA_PI03/WIO**
• GCA129 Multi led indicator interface
• GCA133 Quadruple infra red gate or reflection sensor
• GCA136 4 servo driver (with feed-back) and attachable relay board
• GCA137 Relay board for GCA136 and CAN-GC6
• GCA139 Genli like interface RS232 to Xpressnet
• GCA141c Sensor board for GCA133 and GCA141
• GCA145 Turntable / Fiddleyard controller
• GCA146 Manual control for GCA145
• GCA149 Supplemental relay voor GCA145 for Scale 0, G and 1
• GCA168 Böhler WA2 extension with feed-back and frog/center high current switch
• GCA173 Hall-sensor and/or reed-switch input unit
• GCA173 with different option for wheel counter with opto_slots
• GCA173i connector board
• GCA174 DCC/Motorola decoder
• GCA174MR Decoder for Märklin/Fleischnmann Turnout simulation
• GCA179 isolated hall-sensor and reed-switch input unit → Recommendation for outdoor/garden layouts.
• GCA180 relay extension unit for standard Tuntable control
• GCA186 railroad crossing controller
• GCA186-2 railroad crossing controller with adjustments options
• GCA187 Signal aspect processor
• GCA189 Rail power relay board for fiddle yard
• GCA189-b Main power relay board for fiddle yard
• GCA190 Interface with 8 IR reflection gates for mounting between track sleepers.
• GCA202 Stepmotor controller for 28BY J-48 motor
• GCA204 Railcom display
• GCA214 Loc Identification Receiver for WIO system
• GCA215 Stand alone stepmotor controller for turnouts and mechanical signs
• GCA-RFID support pcb for ID-12(LA) rfid sensor

In the GCA collection there are many sensors available.
Most of them are already mentioned in the extension units.
These sensors are :

• current detection with built in fuses
• combined ground detection for 3-rail, and current detection for 2-rail
• current detection wih zero loss power and high current option
• ground detection, specially made for Märklin three rail
• hall sensors
• active infrared sensors
• RFID sensors
• train detection system

• ORD-3, 3 Amp booster, with regulated and adjustable power
• ORD-3-rc, 3 Amp booster, like previous, and CDE(lenz) and Loc Identification(*) (option).
• ORD-VC-1 High current booster maximum selectable between 1.6 and 20A. CDE(Lenz) and Loc Identificaion(*) (option).

All boosters above are also compatable to be used with LocoNet Railsync.
(*) Loc Identification is compatible with Railcom.

• GCA204 Independant Loc Identification Receiver with display, found on Paco's Official Website
• GCA214 Loc Identificatiion Receiver for WIO system |

• GCA202 driver board for 28BYJ-48 stepper motor

• GCA servo support ServoSet
• GCA215 standalone servo controller

• GCA173 Hall-sensor and reed-switch solution

• MiniPro
• PICADAP4 The adapter for connection of PICPROG3 to GCAxxx and CAN-GCx boards

• GCA82 4 servo Motorola decoder/driver
  
• GCA174 DCC / Motorola Interface for GCA145
  

Optional hardware for the software command station DCC232.

• ORD-3 driver, 3 Amp booster, with regulated and adjustable power, also adaptable to LocoNet Railsync
• S88 GenHSI (Paco)
• GCA98 interface DDX to Edits booster

General DCC decoders based on OpenDCC.

• GCA174 DCC / Motorola Interface for GCA145
  

• GCA139 Xpressnet to PC interface (copy of GenLi)

State of the art car illumination.

• GCA_LM2 Serial Programmable Leds (SPL in Rocrail) Octal Led controller
• BS-1 Universal Led flasher with many -selectable- flashing programs
• Coach Car
• Dutch traction unit "HondeKop"
• Multi colour led control with Arduino nano
• GCA86 dimming interface for 8 leds, to be connected to GCA50/CAN-GC2/GCA_PI02

• GCA140 Standalone controller for cummuter train with extra stops option

• CTC with LNet, CAN or RocNetNode